LaserDistanceLCD - Revision history

Admin: /* Configuration */

2022-11-26T16:55:46Z

Configuration

← Older revision		Revision as of 16:55, 26 November 2022
Line 25:		Line 25:

	== Configuration ==		== Configuration ==
	For the configuration of the device, You must connect the USB cable to the device and to a computer with the installed LaserDistance software. At the time of the configuration, the device doesn't need to be powered over 220VAC, but it can be powered.		For the configuration of the device, You must connect the USB cable to the device and to a computer with the installed [[LaserDistance\|LaserDistance software]]. At the time of the configuration, the device doesn't need to be powered over 220VAC, but it can be powered.

	After You connected the device, start the program, scan for ports, and connect to the port of the LaserDistanceLCD device. If the device was connected, You can see the device picture in the left bottom corner and the measured value in the right bottom corner. The current configuration can be saved to a file for a backup or for later changes.		After You connected the device, start the program, scan for ports, and connect to the port of the LaserDistanceLCD device. If the device was connected, You can see the device picture in the left bottom corner and the measured value in the right bottom corner. The current configuration can be saved to a file for a backup or for later changes.

Admin at 16:17, 26 November 2022

2022-11-26T16:17:42Z

← Older revision		Revision as of 16:17, 26 November 2022
Line 42:		Line 42:

	Strong light can damage the sensor, and influence the measurement. Because of this, don't use this device in direct sun illumination or close to any very hot objects (because of infrared lights).		Strong light can damage the sensor, and influence the measurement. Because of this, don't use this device in direct sun illumination or close to any very hot objects (because of infrared lights).

			== Technical parameters ==
			{\| class="wikitable"
			\|+
			!Power
			\|110/220VAC
			\|-
			!Current
			\|300mA at 220VAC
			\|-
			!Hole size
			\|97 x 72mm
			\|-
			!Sensor
			\|VL53L0X Time-of-Flight (ToF) laser-ranging
			\|-
			!Range
			\|10 - 1200 mm
			\|-
			!Resolution
			\|1mm
			\|-
			!Accuracy
			\|±3%
			\|-
			!Sensor cable length
			\|1 meter
			\|-
			!LCD size
			\|2.9"
			\|}

Admin at 15:49, 26 November 2022

2022-11-26T15:49:13Z

← Older revision		Revision as of 15:49, 26 November 2022
Line 22:		Line 22:
	The sensor has to be mounted with two screws to the "zero point", looking at the 90° to the measured object. The sensor uses 5VDC to power and communicate with the I<sup>2</sup>C protocol.		The sensor has to be mounted with two screws to the "zero point", looking at the 90° to the measured object. The sensor uses 5VDC to power and communicate with the I<sup>2</sup>C protocol.

	The sensor is connected with an JST-XH 4 pin connector to the PCB, over one 1 meter long flat cable.		The sensor is connected with a JST-XH 4-pin connector to the PCB, over one 1-meter-long flat cable.

	== Configuration ==		== Configuration ==
	For the configuration of the device, You must connect the USB cable to the device and to a computer with the installed LaserDistance software. In a time of the configuration, the device ~~don~~'t need to be powered over 220VAC, but it can be powered.		For the configuration of the device, You must connect the USB cable to the device and to a computer with the installed LaserDistance software. At the time of the configuration, the device doesn't need to be powered over 220VAC, but it can be powered.

	After You connected the device, start the program, scan for ports and connect to the port of the LaserDistanceLCD device. If the device was connected, You can see the device picture in left bottom corner, and the measured value in right bottom corner. ~~Current~~ configuration can be saved to a file for a backup or for later changes.		After You connected the device, start the program, scan for ports, and connect to the port of the LaserDistanceLCD device. If the device was connected, You can see the device picture in the left bottom corner and the measured value in the right bottom corner. The current configuration can be saved to a file for a backup or for later changes.

	In the LaserDistance software, You can configure two parameters, the measurement units and the LCD ~~panguage~~. After You changed any parameter, just save it into the device. You don't need to restart the device after it, the changes will be presented ~~inmediately~~ after You save the changes into the device.		In the LaserDistance software, You can configure two parameters, the measurement units, and the LCD language. After You changed any parameter, just save it into the device. You don't need to restart the device after it, the changes will be presented immediately after You save the changes into the device.
	[[File:LaserDistanceLCDUSBandsensor.webp\|alt=LaserDistanceLCD USB and sensor\|center\|thumb\|251x251px\|LaserDistanceLCD USB and sensor]]		[[File:LaserDistanceLCDUSBandsensor.webp\|alt=LaserDistanceLCD USB and sensor\|center\|thumb\|251x251px\|LaserDistanceLCD USB and sensor]]

	=== Measurement units ===		=== Measurement units ===
	By measuring, the device can present the results in millimeters or in inches. Millimeters are SI units while inches are imperial units. The ~~choosed~~ unit will be presented on the LCD panel and in the software window. Also, if You made a measurement into CSV file, it will save in value that is configured in the device.		By measuring, the device can present the results in millimeters or in inches. Millimeters are SI units while inches are imperial units. The chosen unit will be presented on the LCD panel and in the software window. Also, if You made a measurement into a CSV file, it will save in the value that is configured in the device.

	=== Language ===		=== Language ===
	The LaserDistanceLCD supports 18 languages: English, German, French, Italian, Portuguese, Spanish, Dutch, Hungarian, Croatian, Slovenian, Serbian, Czech, Slovak, Polish, Danish, Swedish, Norwegian and Finnish. If You made the changes save it ~~into~~ the device.		The LaserDistanceLCD supports 18 languages: English, German, French, Italian, Portuguese, Spanish, Dutch, Hungarian, Croatian, Slovenian, Serbian, Czech, Slovak, Polish, Danish, Swedish, Norwegian, and Finnish. If You made the changes save them to the device.

	== Maintenance ==		== Maintenance ==
	The device ~~don~~'t require any special maintenance. To have an accurate measurement, check always is the sensor free of dust. If is covered with dust, You will have false measurements. Is important that no other foreign object ~~have~~ to ~~bee~~ between the measuring sensor and the measuring object.		The device doesn't require any special maintenance. To have an accurate measurement, check always if the sensor is free of dust. It is covered with dust, You will have false measurements. Is important that no other foreign object has to be between the measuring sensor and the measuring object.

	~~To strong~~ light can damage the sensor, and to influence the measurement. Because of this, don't use this device in direct sun illumination of close to any ~~wery~~ hot objects (because of ~~infra red~~ lights).		Strong light can damage the sensor, and influence the measurement. Because of this, don't use this device in direct sun illumination or close to any very hot objects (because of infrared lights).

Admin: /* Maintenance */

2022-11-26T12:24:50Z

Maintenance

← Older revision		Revision as of 12:24, 26 November 2022
Line 40:		Line 40:
	== Maintenance ==		== Maintenance ==
	The device don't require any special maintenance. To have an accurate measurement, check always is the sensor free of dust. If is covered with dust, You will have false measurements. Is important that no other foreign object have to bee between the measuring sensor and the measuring object.		The device don't require any special maintenance. To have an accurate measurement, check always is the sensor free of dust. If is covered with dust, You will have false measurements. Is important that no other foreign object have to bee between the measuring sensor and the measuring object.

			To strong light can damage the sensor, and to influence the measurement. Because of this, don't use this device in direct sun illumination of close to any wery hot objects (because of infra red lights).

Admin at 12:21, 26 November 2022

2022-11-26T12:21:38Z

← Older revision		Revision as of 12:21, 26 November 2022
Line 37:		Line 37:
	=== Language ===		=== Language ===
	The LaserDistanceLCD supports 18 languages: English, German, French, Italian, Portuguese, Spanish, Dutch, Hungarian, Croatian, Slovenian, Serbian, Czech, Slovak, Polish, Danish, Swedish, Norwegian and Finnish. If You made the changes save it into the device.		The LaserDistanceLCD supports 18 languages: English, German, French, Italian, Portuguese, Spanish, Dutch, Hungarian, Croatian, Slovenian, Serbian, Czech, Slovak, Polish, Danish, Swedish, Norwegian and Finnish. If You made the changes save it into the device.

			== Maintenance ==
			The device don't require any special maintenance. To have an accurate measurement, check always is the sensor free of dust. If is covered with dust, You will have false measurements. Is important that no other foreign object have to bee between the measuring sensor and the measuring object.

Admin: /* Configuration */

2022-11-26T12:04:18Z

Configuration

← Older revision		Revision as of 12:04, 26 November 2022
Line 30:		Line 30:

	In the LaserDistance software, You can configure two parameters, the measurement units and the LCD panguage. After You changed any parameter, just save it into the device. You don't need to restart the device after it, the changes will be presented inmediately after You save the changes into the device.		In the LaserDistance software, You can configure two parameters, the measurement units and the LCD panguage. After You changed any parameter, just save it into the device. You don't need to restart the device after it, the changes will be presented inmediately after You save the changes into the device.
			[[File:LaserDistanceLCDUSBandsensor.webp\|alt=LaserDistanceLCD USB and sensor\|center\|thumb\|251x251px\|LaserDistanceLCD USB and sensor]]

	=== Measurement units ===		=== Measurement units ===

Admin: /* Measurement units */

2022-11-26T11:58:24Z

Measurement units

← Older revision		Revision as of 11:58, 26 November 2022
Line 33:		Line 33:
	=== Measurement units ===		=== Measurement units ===
	By measuring, the device can present the results in millimeters or in inches. Millimeters are SI units while inches are imperial units. The choosed unit will be presented on the LCD panel and in the software window. Also, if You made a measurement into CSV file, it will save in value that is configured in the device.		By measuring, the device can present the results in millimeters or in inches. Millimeters are SI units while inches are imperial units. The choosed unit will be presented on the LCD panel and in the software window. Also, if You made a measurement into CSV file, it will save in value that is configured in the device.

			=== Language ===
			The LaserDistanceLCD supports 18 languages: English, German, French, Italian, Portuguese, Spanish, Dutch, Hungarian, Croatian, Slovenian, Serbian, Czech, Slovak, Polish, Danish, Swedish, Norwegian and Finnish. If You made the changes save it into the device.

Admin at 11:56, 26 November 2022

2022-11-26T11:56:35Z

← Older revision		Revision as of 11:56, 26 November 2022
Line 29:		Line 29:
	After You connected the device, start the program, scan for ports and connect to the port of the LaserDistanceLCD device. If the device was connected, You can see the device picture in left bottom corner, and the measured value in right bottom corner. Current configuration can be saved to a file for a backup or for later changes.		After You connected the device, start the program, scan for ports and connect to the port of the LaserDistanceLCD device. If the device was connected, You can see the device picture in left bottom corner, and the measured value in right bottom corner. Current configuration can be saved to a file for a backup or for later changes.

	In the LaserDistance software, You can configure two parameters, the measurement units and the LCD panguage.		In the LaserDistance software, You can configure two parameters, the measurement units and the LCD panguage. After You changed any parameter, just save it into the device. You don't need to restart the device after it, the changes will be presented inmediately after You save the changes into the device.

			=== Measurement units ===
			By measuring, the device can present the results in millimeters or in inches. Millimeters are SI units while inches are imperial units. The choosed unit will be presented on the LCD panel and in the software window. Also, if You made a measurement into CSV file, it will save in value that is configured in the device.

Admin: /* Configuration */

2022-11-26T11:43:43Z

Configuration

← Older revision		Revision as of 11:43, 26 November 2022
Line 25:		Line 25:

	== Configuration ==		== Configuration ==
	For the configuration of the device, You must connect the USB cable to the device and to a computer with the installed LaserDistance software.		For the configuration of the device, You must connect the USB cable to the device and to a computer with the installed LaserDistance software. In a time of the configuration, the device don't need to be powered over 220VAC, but it can be powered.

	After You connected the device, start the program, scan for ports and connect to the port of the LaserDistanceLCD device.		After You connected the device, start the program, scan for ports and connect to the port of the LaserDistanceLCD device. If the device was connected, You can see the device picture in left bottom corner, and the measured value in right bottom corner. Current configuration can be saved to a file for a backup or for later changes.

	In the LaserDistance software, You can configure two parameters, the measurement units and the LCD panguage.		In the LaserDistance software, You can configure two parameters, the measurement units and the LCD panguage.

Admin at 11:39, 26 November 2022

2022-11-26T11:39:56Z

← Older revision		Revision as of 11:39, 26 November 2022
Line 28:		Line 28:

	After You connected the device, start the program, scan for ports and connect to the port of the LaserDistanceLCD device.		After You connected the device, start the program, scan for ports and connect to the port of the LaserDistanceLCD device.

			In the LaserDistance software, You can configure two parameters, the measurement units and the LCD panguage.