LaserDistanceControl

From RAPMAS
Revision as of 12:46, 13 December 2022 by Admin (talk | contribs) (→‎Configuration)
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to navigation Jump to search

Overview

LaserDistanceControl LCD Main
LaserDistanceControl LCD Main

LaserDistanceControl is a panel-mount controller and measurement device. Two relays can be used to control any process and two alarming sources of information about a critical value. It uses laser light to measure the distance between the sensor and the object. The measurement is based on the ToF (time of flight) of light from the source (sensor) and is the reflection (object).

The measured distances can be shown in millimeters (mm) or inches (inches) in 18 different languages. Also, the device can be used to write measurement results in CSV files. Configuration of a device is made with LaserDistance software.

Hardware installation

The LaserDistanceControl has to be mounted on a panel. The hole diameters have to be 97 x 72mm. The backside of the device is 45mm deep, so leave enough place to connect the cables. Powering off the device can be done with 220VAC or 110VAC. The sensor is connected with a 1-meter-long flat cable to the device.

By the installation place, please note that a device is about 45mm bold, so You have to leave enough place to access the cables and connectors from the sensor and the programmer.

The sensor has two mounting holes, 20mm distance. By the mounting of the sensor, note that it needs to have a clear view of the measured object. Don't install the device in a humid environment, water tanks, etc. Also, the device must be used indoors and is not made for outdoor usage. Presents of high dust can affect the measurement. The possibility to reflect laser light can affect the measuring range.

Powering

LaserDistanceControl uses 220VAC for powering. The power connector is on the back side in the bottom left corner, marked on the PCB with "220V". Next to the powering terminal screw, is the switching port, marked on the PCB with "P-SW1". It interrupts the powering of the device. If You need this function, just install an interrupter for 220VAC. In case You don't need this function, just shortcut it, because if You remove the wire on that connector, the device still stays not powered. For the wiring, use 1.5mm2 cable, the maximal current that a device need is under 300mA at 220VAC.

LaserDistanceControl Power
LaserDistanceControl Power

Sensor installation

Sensing of the distance is done with the Time of Flight technique (ToF), provided by the STMicroelectronics VL53L0X ranging sensor. It has a measuring range of up to 1200mm in ideal condition.

The sensor has to be mounted with two screws to the "zero point", looking at the 90° to the measured object. The sensor uses 5VDC to power and communicate with the I2C protocol.

The sensor is connected with a JST-XH 4-pin connector to the PCB, over one 1-meter-long flat cable.

LaserDistanceControl VL53L0X Sensor
LaserDistanceControl VL53L0X Sensor

Relay installation

The device has two independent relays. Bot relays can be configured to be triggered or disabled by software. The maximal current by short intervals that can be switched is 10A by 220VAC. Continuous powering (more than 10 minutes or more than 6A) is recommended to use a contractor and to power the contractor from the relays. Continuously usage of relays over 10A for a long time can produce overheating and damage the device.

To cable the relays, use 1.5mm2 wire. On the PCB are tree terminal crews per relay, marked with NC, COM, and NO. NC means Normally Closed, COM is Common and NO is Normally Open. The current state of the replays is presented also with a LED on the PCB surface.

LaserDistanceControl Relays
LaserDistanceControl Relays

Configuration

LaserDistanceControl USB and Sensor
LaserDistanceControl USB and Sensor

For the configuration of the device, You must connect the USB cable to the device and a computer with the installed LaserDistance software. At the time of the configuration, the device doesn't need to be powered over 220VAC, but it can be powered.

After You connected the device, start the program, scan for ports, and connect to the port of the LaserDistanceControl device. If the device was connected, You can see the device picture in the left bottom corner and the measured value in the right bottom corner. The current configuration can be saved to a file for a backup or later changes.

In the LaserDistance software, You can configure multiple parameters, the measurement units, LCD language, alarming, and relay. After You changed any parameter, just save it into the device. You don't need to restart the device after it, the changes will be presented immediately after You save the changes into the device.

Relays and alarms

The relays and the alarm have three possible operational states:

  • disabled - there is no action, the control is set to off
  • if above - the alarm or the relay will be triggered if the distance rises above the defined value
  • if below - the alarm or the relay will be triggered if the distance falls under the defined value

Measurement units

By measuring, the device can present the results in millimeters or inches. Millimeters are SI units while inches are imperial units. The chosen unit will be presented on the LCD panel and in the software window. Also, if You measured a CSV file, it will save in the value that is configured in the device.

Language

The LaserDistanceControl supports 18 languages: English, German, French, Italian, Portuguese, Spanish, Dutch, Hungarian, Croatian, Slovenian, Serbian, Czech, Slovak, Polish, Danish, Swedish, Norwegian, and Finnish. If You made the changes save them to the device.

Maintenance

The device doesn't require any special maintenance. To have an accurate measurement, check always if the sensor is free of dust. It is covered with dust, You will have false measurements. Is important that no other foreign object has to be between the measuring sensor and the measuring object.

Strong light can damage the sensor, and influence the measurement. Because of this, don't use this device in direct sun illumination or close to any very hot objects (because of infrared lights).

Technical parameters

Power 110/220VAC
Current 300mA at 220VAC
Hole size 97 x 72mm
Sensor VL53L0X Time-of-Flight (ToF) laser-ranging
Range 10 - 1200 mm
Resolution 1mm
Accuracy ±3%
Sensor cable length 1 meter
LCD size 2.9"
Relay current maximal 10A at 220AC